Screw press Instructions 1. Before use, you must read the instruction manual, are familiar with the performance characteristics and operating methods of the machine. 2. Before the boot, must conduct a comprehensive inspection, not loose fasteners, handle rotation flexibility, hand rotating pulley, each operating parts should be normal, no abnormal sound, followed by filling 30 # oil in reducer. 3. Loosen the lock nut, turn the adjustment screw (adjusted by turning the handle counter-clockwise, the cake space narrowing, the adjustment handle clockwise, the cake gap widened) so squeezed tight against the cone snail cake circle The cone screw press, then unscrew the adjustment screw clockwise (spin out 3-5 laps), then tighten the nut, ready to boot. 4. The machine connected three-phase four-wire power supply, the new press, the spindle should be made after the power is turned counter-clockwise, in any circumstances, the machine must have a good grounding device, or can not boot. 5. Adjust the temperature controller (2) to the press the desired temperature 120 ℃ -160 ℃ (according to oil may be) the heating switch position open to a host heating, heating up the machine, then the green light on the temperature controller, red light is off, when the engine temperature rises to a set temperature, and the red light green light extinguished, the temperature of the machine is automatically controlled and maintained at the set temperature, low winter temperatures, the heating switch open to host all the heating position, the oil pan temperature, easy oil left. 6. Press the main motor button (the host switch to a positive open position) host starts running, it should be counter-clockwise direction of rotation. . Screw press pressing screw installation methods: First: spiral when pressing screw press installation, pressing bolts narrow end we want to press the upward spiral of rising, then tapping screw stub and pressed by number descending arranged in turn mounted on the shaft, installed after adding asbestos gaskets. Second: In order to prevent infiltration of diesel locknut to press, fitted with bearings, mediation bolts, after this is done, we should pay attention to press installed two bearings are large bore surface side against the adjusting bolt ends , pressing bolts together with nuts overall installed after two M42 × 2 back tight, pay attention to both the bearing clearance at the back tight. Third: turn the adjustment screw by hand to move, you can flexibly rotate on the line. Screw press pressing screw disassembly methods: First: stop moving immediately after the press handle, squeeze out of the shaft, remove the protective cap, round nuts, bearings and adjust the bolts. Second: with iron bars inserted into the hole of the lock nut counterclockwise rotation, after remove the lock nut, pressing bolts can be easily disassembled. Third: the fuel tank should be kept clean after every few months or so should wash tank hydraulic press, and replaced with new oil, or the oil tank remove the filter before use. Otherwise impurities within the oil will cause the oil pump wear and blockage of press work. Fourth: As oil extraction of different materials, so depending on the fuel, master cake pressed into the billet temperature and moisture content, when the pressing, the lower the top plate to minimize the position, loosen the tie rod nuts activities, unplug the two active pin, rotate the lever on the side activities. Fifth: cake bore successively charged, after pressing, the active lever back in situ fixed, pre-press to see first oil lasts, return of the piston, the remaining cake into the official press. Sixth: The pressure oil pump to filter, the concentration is not too large, it is best to use canola oil, soybean oil and peanut oil, etc., prohibit the use of gasoline, kerosene and other flammable oil. Automatic oil should be installed for indoor use, in order to avoid an open-air wind and rain, causing rust and cooking oil pollution. Press price _ heyday Machinery (certified) _ press provided by Zhengzhou Dingsheng Machinery Manufacturing Company Limited. Zhengzhou Dingsheng Machinery Manufacturing Co., Ltd. (www.zhayouji6.cn) is Zhengzhou, edible oil processing machinery leaders, over the years, the company is implementing the scientific management, innovation and development, the principle of honesty and trustworthiness, and satisfy customer needs. In the heyday Machinery leadership with the staff warmly welcome all inquiries negotiations to create a better future heyday Machinery.